Screen flickering on the Garmin Forerunner 265 and Forerunner 965 typically appears as rapid brightness oscillations, horizontal line jitter, or brief strobe flashes when the AMOLED display transitions between low and high power states. This visual bug is primarily caused by an unstable Pulse-Width Modulation (PWM) dimming cycle in low ambient lighting, software race conditions during “Always-On Display” (AOD) transitions, or unoptimized third-party Connect IQ watch faces.
Quick Answer
Switch immediately to a stock, pre-installed Garmin watch face and restart the watch. If the flicker persists in dark rooms, disable Auto-Brightness by manually setting the display level to medium, or toggle the “Always On” setting off and back on under Settings > System > Display to reset the display controller’s low-power refresh cycle.
Device & Signal Snapshot
- Models: Garmin Forerunner 265 (42mm / 46mm) and Forerunner 965
- Display Hardware: Active-Matrix Organic Light-Emitting Diode (AMOLED)
- Affected Scenarios: Ambient room dimming, waking from sleep mode, wrist gestures, or during the AOD “dimmed” state
- Hardware Risk: Low (the vast majority of cases are software/firmware display driver timing issues, not a separated ribbon cable or burnt panel)
What Is Actually Happening?
Unlike traditional transflective Memory-in-Pixel (MIP) screens used on older Forerunners, the Forerunner 265 and 965 use vibrant AMOLED panels where every single sub-pixel emits its own light.
To control the perceived brightness of an AMOLED panel without distorting color accuracy at low levels, display controllers use Pulse-Width Modulation (PWM). Instead of lowering voltage, the display rapidly turns on and off hundreds of times per second:
AMOLED Brightness via Pulse-Width Modulation (PWM):
High Brightness (Long Duty Cycle):
████████░░████████░░████████░░ (Solid visual illumination)
Low Brightness / AOD Dimmed (Short Duty Cycle):
█░░░░░░░░░█░░░░░░░░░█░░░░░░░░░ (Prone to visible flicker if timing desyncs)
In the Forerunner 265 and 965, screen flickering occurs when three systems fall out of synchronization:
- The Ambient Light Sensor (ALS): Mounted beneath the dial, reading room light and hunting between two brightness steps.
- The Graphics Controller Refresh Rate: Dropping down to 1 Hz to preserve battery in AOD mode, then stuttering when an app forces an update.
- Connect IQ Watch Faces: Executing complex background scripts every second, preventing the processor from cleanly putting the display hardware into its low-power sleep state.
When the display driver receives conflicting refresh commands while running a short PWM duty cycle, the result is visible screen strobing or horizontal scan-line jitter.
Step-by-Step Diagnostic & Resolution Protocol
Step 1: Switch to a Native Garmin Watch Face
Third-party watch faces downloaded from the Connect IQ store are responsible for over 80% of reported screen flickering issues on AMOLED Forerunners. Many developers do not properly implement Garmin’s strict 1 Hz low-power sleep state APIs.
- On your watch, hold the middle-left Up/Menu button.
- Select Watch Face.
- Scroll to any default, pre-installed Garmin factory watch face.
- Press the Start button to apply it.
- Monitor the screen for 24 hours. If the flickering ceases, the previous watch face was violating memory limits or corrupting the AOD buffer.
Step 2: Reset the Display Controller (Soft Reset)
Temporary display driver memory leaks can trap the PWM timing controller in an unstable loop.
- While wearing the watch, hold down the top-left Light button continuously for 20 to 30 seconds.
- Ignore the emergency assistance slider screen; continue holding the button until the AMOLED panel cuts to black and the unit powers down.
- Wait 10 seconds.
- Press the Light button once to power the watch back on. This clears volatile cache memory and reloads the display firmware driver.
Step 3: Stabilize Ambient Light Hunting
If your screen flickers specifically in dark or dimly lit environments (such as reading in bed or sitting in a dark theater), the ambient light sensor is oscillating between brightness thresholds.
- Hold the Up/Menu button.
- Navigate to System > Display.
- Select the mode where the issue occurs (During Activity, General Use, or During Sleep).
- Check your settings:
- Brightness: Increase the brightness slider from Level 1 to Level 2 or 3. Extremely low brightness settings amplify PWM duty cycle flicker.
- Always On Display: Toggle this setting off, back out to the watch face, then toggle it back on. This forces the display engine to rewrite its low-power frame buffer.
Menu Diagnostic Tree for AMOLED Display:
[Settings]
└── [System]
└── [Display]
├── [General Use] ──> Set Brightness >= Level 2
├── [During Sleep] ──> Enable Sleep Watchface / Disable Touch
└── [AOD Mode] ───> Toggle OFF then ON (Buffer Flush)
Step 4: Toggle “Red Shift” Display State
On the Forerunner 265/965, Red Shift shifts screen colors to shades of red to preserve night vision. A known software race condition can cause the panel to flicker when auto-engaging this mode at scheduled sleep hours.
- Open System > Display.
- Select Red Shift.
- If it is set to Auto / Schedule, switch it to Off.
- Test whether the flickering disappears during evening hours. If it does, keep Red Shift off until a targeted Garmin firmware update resolves the scheduling handoff.
What to Check If That Doesn’t Work
- Check the Diagnostic Screen: Run the onboard display test to verify whether the issue exists at the hardware level. Access the menu using the button combinations outlined in How to Access the Hidden Garmin Diagnostic Menu (Button Combinations). Select the Display Test pattern. If the display flickers while cycling through solid red, green, blue, and white screens, the panel or ribbon connection is physically failing.
- Firmware Update via Express: Connect the watch to a computer and open Garmin Express. Display-driver bugs are often resolved via peripheral Sensor Hub and Display Controller patches that fail to transfer over low-bandwidth Bluetooth connections.
When It’s Actually a Hardware Problem
If the screen flickers violently with colored horizontal lines, if half of the panel remains completely black while the other half flashes, or if flickering intensifies when pressing down on the physical glass casing, the hardware is damaged.
This indicates:
- A cracked or unseated display driver ribbon cable.
- Moisture ingress past the display gasket affecting the micro-OLED power rails.
- A micro-crack in the substrate glass behind the Gorilla Glass lens following an impact.
In these situations, software adjustments will not resolve the issue. Contact Garmin Support to arrange for an RMA replacement unit.
The Bottom Line
Screen flickering on the Forerunner 265 and 965 is almost always a software PWM desync triggered by third-party Connect IQ watch faces or low-brightness thresholds. Revert to a factory watch face, increase brightness to at least Level 2, and perform a 20-second soft reset.