How to Fix the “Red X” on Your Fitbit Luxe Screen

A Red X on your Fitbit Luxe screen means the tracker hit a critical firmware or reset error—most often right after an interrupted software update or a failed factory reset. Because the Fitbit Luxe has no physical button on the watch body, you have to restart it using the button built into the USB end of its charging cable before re-syncing or re-adding it in the Fitbit app.

Quick Answer

Plug your Fitbit Luxe into its charging cable connected to a wall outlet, then press the small button on the flat USB plug three times within eight seconds (pausing one second between presses). Once the Luxe vibrates and restarts, open the Fitbit app to finish syncing or reinstall the interrupted firmware update.

Device and Signal Snapshot

  • Affected Devices: Fitbit Luxe
  • Affected Function: Firmware verification, factory reset completion, and operating system boot
  • Severity: High—the tracker stays locked on the Red X screen and cannot track until firmware or sync recovers
  • Data Risk: Moderate—if the Luxe requires removing and re-adding in the app to reload firmware, any unsynced data left on the band will be wiped

What Is Actually Happening?

The Red X appears when the Fitbit Luxe starts writing new firmware or clearing user data and gets interrupted before finishing. Common triggers include pulling the Luxe out of Bluetooth range during a firmware download, losing battery mid-update, or triggering an erase from the watch menu without completing the sync handshake in the Fitbit app.

On the Luxe, that Red X frequently pairs with an alert inside the app (or across the screen) reading "Data not cleared, Sync & try again". Until the Luxe reboots cleanly and completes its handshake with the Fitbit app, it blocks normal operation so corrupted system files do not run.

What Can Cause the Red X on Fitbit Luxe

  • Interrupted firmware update: Phone screen locking, Bluetooth dropping, or low battery during an update leaves broken OS files behind.
  • Incomplete factory reset (“Erase User Data”): Starting a reset on the band without syncing it cleanly afterward often lands right on the Red X.
  • Dirty charging pins or unstable power: Poor contact on the magnetic charger drops power right as the Luxe tries to verify its update.
  • Corrupted onboard flash memory: Less often, aging internal storage fails to write system files cleanly even on a full battery.

What to Do First

1. Clean the Charging Contacts and Plug Into a Wall Outlet

Wipe the gold charging contacts on the back of the Luxe and the pins on the charger clip so power stays rock-solid; if you see residue or buildup, follow How to Clean Wearable Charging Pins: The Eraser vs. Alcohol Method. Plug the USB cable into a wall adapter rather than a laptop port and let it sit for 15 to 20 minutes.

2. Perform the Charging-Cable 3-Press Restart

Because the Fitbit Luxe is completely buttonless on the tracker body, use the reset button built into its official charging cable:

  1. Leave the Luxe snapped onto the plugged-in charging cable.
  2. Locate the small button on the flat USB-A end of the cable.
  3. Press that button three times within eight seconds, pausing for roughly one second between each click.
  4. Wait about 10 seconds for the Luxe to vibrate and show the Fitbit logo.

(Note: If the cable button does nothing, unplug the USB cable, plug it back into a different wall brick, re-seat the Luxe tightly, and repeat the three presses cleanly.)

3. Sync and Finish Any Pending Update in the Fitbit App

Keep your Luxe on the charger right next to your phone and open the Fitbit app:

What to Check If That Doesn’t Work: Remove and Re-Add the Luxe

If the Luxe stays on the Red X after restarting via the cable—or connects briefly and refuses to clear the error—re-establishing the device from scratch inside the Fitbit app usually forces a clean firmware reload:

  1. Open your phone’s Settings > Bluetooth, locate Luxe, and select Forget This Device.
  2. Open the Fitbit app, tap the Devices icon in the top-left corner, select your Luxe, and tap Remove This Luxe (confirming removal).
  3. Restart your phone, turn Bluetooth back On, and perform the 3-press USB cable restart on your Luxe one more time while it stays plugged in.
  4. In the Fitbit app, tap Add More Devices > Luxe and complete the fresh pairing and firmware setup right beside your phone.

(Warning: Removing the Luxe from your account clears any unsynced steps or sleep still sitting on the tracker, though everything already synced to your account remains safe in the cloud.)

When It’s Actually a Hardware Problem

Stop troubleshooting and contact Fitbit/Google Support if any of the following happen:

  • The 3-press USB cable restart produces no vibration and leaves the Red X permanently frozen across two different power outlets (or a second genuine Luxe charging cable).
  • Removing and re-pairing the Luxe fails because the tracker never broadcasts a Bluetooth pairing code during setup.
  • Fresh firmware installation completes in the app, and the Luxe immediately reboots right back to the Red X.

If you encounter a different icon or numeric failure during recovery, check Fitbit Legacy Error Codes & OS Sync Failures.

Bottom Line: Never hunt for a button on the Fitbit Luxe body—clean the gold pins, plug into a wall outlet, run the 3-press restart using the button on the USB charging plug, and re-pair inside the Fitbit app to push clean firmware if the Red X stays stuck.